Browse all practice questions for the GoJet Systems Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

GoJet Systems Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • In the event of a jammed aileron or elevator, how can the pilot regain control of the operable control surface?
  • The Engine and APU areas are protected by ___ fire detection loops. Normally ___ loops must detect a fire/overheat condition to produce the appropriate warning indications
  • Loss of hydraulic system ___ will cause the nosewheel steering to go into free castoring mode.
  • Which hydraulic system's loss would cause nose wheel steering to go into free castoring mode?
  • What does the roll disconnect T-handle do to the control wheels?
  • Extinguishing an APU fire is accomplished through the use of which bottle?
  • If DME hold is selected, you will not be able to use the VOR course information for ILS or VOR tracking if you select another frequency.
  • If the bi-directional XFLOW pump fails to turn on when the fuel imbalance reaches 200 lbs, which remedy is allowed?
  • What is the normal CF34 thrust rating?
  • What is the minimum pavement width for a 180 degree turn?
  • What is the maximum speed for the operation of the windshield wipers?
  • What is the minimum engine fuel temperature prior to takeoff, and the minimum bulk fuel temperature depending on fuel type?
  • Drain mast heating control relies on which signal?
  • APU fuel is drawn from which tank?
  • In EICAS terminology, which color is used to indicate warnings?
  • OEO fuel scheduling from FADEC will occur with the N1 speed difference between the engines exceeds what percentage?
  • Select the statement that correctly describes heating with 115VAC and ON/OFF conditions.
  • The APU can be used as a source of bleed air for the aircraft ice protection systems.
  • When the High Pressure Bleed valve on the 10th stage is providing air, what effect does this have on the 6th stage?
  • To fly a full ILS approach with glideslope, you should select the NAV mode of the FCP.
  • Under which condition does the AILC schedule use a higher temperature?
  • What does the AC ESS XFER switch light do when selected?
  • Identify the statement in which only the true heating condition is stated.
  • Continuous ignition must be on during which condition?
  • Under what condition are the probes automatically heated?
  • What does the half-bank mode provide?
  • Following ED1 failure, which actions will display the EICAS status page?
  • How many hydraulic systems provide redundant power to the PCUs?
  • Where is the slip indicator located?
  • The primary source of AC electrical power is the ___.
  • What does EMER FLAP do?
  • Which window heat setting heats only the windshields at the higher level?
  • What happens to the water extracted from the conditioned air produced by the A/C packs?
  • Which system automatically controls proper operation during engine start instead of manual pilot action?
  • Which setting corresponds to a Vfe of 185 knots for flap setting F30?
  • Which control allows routing bleed air from the good engine to both wings for wing anti-ice after engine failure?
  • Which cockpit light is powered by the battery bus and will cause the battery to be drained, even when the battery master switch is OFF?
  • How many wing anti-ice schedules are there?
  • On the ground, air exhausted from the cooling displays and the avionics area exits the aircraft through ___?
  • ENG Ignition power sources?
  • If both sources of power to FADEC fail, what will happen to the engine?
  • Where does air exhausted from cooling displays exit on the ground?
  • If low fuel is detected in the left engine fuel feed line, which boost pumps activate?
  • Which statement about the hydraulic quantity readout is true?
  • APU start limits specify how many attempts in one hour with what delays?
  • When a hydraulic pump switch is set to AUTO, the pump will automatically start when an AC generator is online and ___.
  • How many idle power settings are available from FADEC?
  • Which statement best describes DC power supply in this system?
  • During a one-engine-out event, FADEC will schedule APR power when the thrust lever is in which detent?
  • What are the Vfe speeds for the selected flap settings?
  • Which statement best describes the heating behavior when 115VAC is applied and ON/OFF state may be either?
  • Which option best describes how avionics are cooled?
  • If there is a failure of motive flow, is it possible to get fuel into the collector tanks?
  • What is the warning associated with discharging a portable fire extinguisher in the flight deck?
  • During roll disconnect, what does the SSCU do to maintain lateral control?
  • Do the vibration limit gauges alert the pilot for both N1 and N2, only N1, or only N2?
  • What are the APU start limits?
  • What effect will the loss of either the #2 or #3 hydraulic system have on braking capability?
  • When do passenger oxygen masks deploy?
  • If the ED1 screen fails, which ED will automatically display ED1 information?
  • What is the minimum airspeed required for proper operation of the ADG generator?
  • Hydraulic systems 1 and 2 are each powered by which combination?
  • Which detent is associated with APR power during an OEO scenario?
  • During an APU fire protection activation in flight, what happens to the APU?
  • What does the EMER FLAP switch do?
  • What are the amp-hour ratings for the Main and APU batteries?
  • What happens if the APU detects a fire on the ground?
  • What is the purpose of the ESS TRU 2 Tie Contractor?
  • Which statement about the automatic seatbelt illumination in AUTO mode is true?
  • Bleed air leaks are detected by which mechanism?
  • If DME hold is selected, you can still use the VOR course information for ILS or VOR tracking when another frequency is selected.
  • If ground spoilers fail to deploy, which switch setting is used to arm them for deployment?
  • Two safety valves in the aft bulkhead serve to ___?
  • What is the APR thrust rating for the CF34?
  • Which battery has the higher Ampere-Hour rating?
  • What do the L/R ENG FIRE PUSH switch light do?
  • Which pump is powered by both ADG and AC BUS 1?
  • What does CSD stand for?
  • Which combination triggers the stab trim warning clacker?
  • During a wind shear warning, you should increase pitch up to the Pitch Limit Marker (alpha-margin indicator).
  • In AUTO mode, besides the AC generator being online, what condition must be met for the pump to start?
  • True or False: Individual satellites can be deselected from use by entering the satellite ID on the FMS GPS Control Page.
  • Prior to APU start, the minimum battery voltage must be present on both batteries is
  • With the cockpit switch in ARM, emergency lighting activates if there is a loss of power to which buses?
  • How is the engine oil temperature kept under control?
  • How do you manually transfer fuel?
  • What type of engine air bleed valves are installed on the CRJ?
  • How many EDP hydraulic pumps are on the CRJ-700?
  • What pressure do PRSOVs limit the pneumatic system to?
  • Which power source powers the cockpit voice recorder?
  • The N2 compressor consists of how many stages and is connected to which turbine?
  • What is the maximum altitude for single A/C pack operation?
  • What is the normal power source for the AC ESS BUS?
  • Which status does the Flight Mode Annunciator (FMA) display on the PFD?
  • What is the normal hydraulic reservoir quantity?
  • What provides cooling air for hydraulic systems 1 and 2 during ground operations?
  • On which sides of the aircraft are the oxygen overboard discharge indicator and the oxygen servicing panel located?
  • How many TRUs are included in the DC electrical system?
  • What is the maximum positive cabin pressure differential?
  • Which action sequence correctly enables a cabin announcement on the Public Address System?
  • The bi-directional XFLOW pump turns on and auto XFLOW begins when the fuel imbalance reaches how many pounds?
  • Which statement describes TOGA engagement in flight?
  • Fire detection in the forward cargo compartment is accomplished with how many detectors?
  • What does the ADG Power supply?
  • When the active Cabin Pressure Controller fails, what happens automatically?
  • When the ECP is inhibited following ED failure, what happens to the status and synoptic pages?
  • During GPS signal loss, how does the bearing pointer on the MFD respond?
  • The nosewheel steering system allows travel from neutral with the handwheel control unit?
  • If the primary cabin pressure controller becomes unavailable, the system will
  • If slat travel stops, will the flaps continue to their selected position?
  • The turbulence penetration speed uses which units to specify its value, relative to Mach?
  • In the event of power failure of the EICAS Control Panel, what buttons will be operational?
  • What will the APU automatic fire protection provide in flight?
  • The AFCS automatically selects 1/2 bank at what altitude?
  • When the Captain's NORM/EMER switch on the ACP is set to EMER, what happens?
  • What two conditions will result in an automatic manual disconnect of the IDG?
  • Back course localizer approaches should be flown with the NAV button selected.
  • What ED2 message appears when one flap motor fails and the other runs at half speed?
  • Which hydraulic systems must be powered when checking brake wear?
  • The statement 'All fuel tanks can be serviced by utilizing the overwing filler caps' is:
  • After an overheated brake is cooled in flight by lowering the gear, how can the pilot reset the BTMS indicated system?
  • How is the Anti-Skid test performed?
  • At what altitude does the AFCS automatically select 1/2 bank?
  • On a GPS approach, you may continue to the missed approach point when GPS APPR appears at the bottom of the NAV source info block on the PFD.
  • To make a cabin announcement on the PA system, what should you do?
  • Which statement accurately describes the number of idle power settings available from FADEC?
  • Which statement best describes the roll disconnect function on lateral control?
  • If the only operative ED is displaying a status or synoptic page and a DCU warning occurs, what should happen?
  • The crew oxygen system will supply 100% oxygen at an altitude of __ regardless of the setting.
  • How many Halon bottles are used by the cargo fire protection system?
  • Which bleed valves fail in the closed position?
  • Which switch position allows conditioned air to cool the flight deck CRT displays?
  • Under which condition would BLEED MISCONFIG appear on EICAS?
  • From which tank is the APU's fuel supplied?
  • Which system component sends fuel from the center tank to the engines or APU?
  • How many transformer rectifier units supply DC power?
  • The Flight Mode Annunciator provides status for which function?
  • Is it true that releasing the IDG DISC switchlight after pressing it regains the generator?
  • Which statement best describes how satellites can be deselected for use?
  • How can the Hydraulic SOV be closed to interrupt fluid to the EDP?
  • What type of engine air bleed valves are installed on the CRJ-700?
  • Which statement reflects the heating condition as described?
  • What are the flap handle gate positions?
  • Which item is not part of the AC bus power priority?
  • What function does the roll disconnect perform?
  • What is the engine ignition powered by?
  • In flight, what does the APU automatic fire protection do?
  • What is the maximum altitude for single pack operation?
  • Which door is not displayed on the DOORS synoptic page?
  • What does Flight Abort Mode do after takeoff?
  • In a runaway trim situation, which action disconnects the trim?
  • Which response occurs when one wing tip navigation light bulb fails?
  • How many engine-driven hydraulic pumps are on the CRJ?
  • Pitot Tubes P1 and P2 are pitot-static tubes while P3 is only a pitot tube.
  • The forward cargo detection uses how many detectors?
  • Which pitot tube is described as 'pitot-only'?
  • DC power is supplied by ________.
  • Which statement confirms that the ON/OFF state does not affect heating when 115VAC is applied?
  • What is the purpose of the isolation valve?
  • If ESS TRU 1 and ESS TRU 2 fail, how would the DC ESS BUS remain powered?
  • The APU starter cut-out range is used to define what RPM range?
  • What is the path for condensate water from the conditioned air in the air conditioning packs?
  • What is the required procedure to make a cabin announcement using the Public Address System?
  • What is the purpose of the check valve on the 6th stage bleed line?
  • If motive flow is lost, how are the collector tanks kept full?
  • How many smoke detectors are in the forward cargo and aft cargo?
  • If one of the DCU disable switch lights is pressed, all voice messages will be inhibited except for __ and __ warnings
  • The loss of hydraulic system ___ will prevent the nose gear from extending, even when using the alternate gear extension procedures.
  • How is the galley air heated?
  • Which components move fuel from the main tanks to the engines or APU?
  • If the EMER FLAP switch is set to DEPLOY above the flap limit airspeed of 230 kts, what happens to the flaps/slats?
  • Which switch position allows conditioned air to cool the cockpit CRT displays?
  • During start, the thrust lever should be moved from shutoff at what percent N2?
  • A red CABIN ALT message indicated that the cabin altitude exceeds ___ ft. An amber CABIN ALT message indicates the cabin altitude is ___.
  • Bypass air from the N1 fan produces approximately what percent of the engine thrust?
  • How do you manually transfer fuel?
  • When does bleed air switching occur during landing?
  • Where does the hydraulic pump 3B receive its power?
  • What occurs when the cargo fire protection discharge switchlight is pressed?
  • When the parking brake is set and hydraulic systems are deactivated, what happens to brake pressure?
  • Which statement about the nominal hydraulic pressure is true?
  • Which combination of cues is commonly observed during a Red Warning on ED1?
  • Primary source for the potable/wash water system (PWS)?
  • Which items are powered by the DC EMER BUS?
  • Which of the following is true about the number of automatic cabin pressure controllers?
  • The flight director will provide wind shear escape guidance during both a wind shear caution and a wind shear warning from the EGPWS system.
  • During extreme pitch or bank attitudes, what action does the PFD take to improve readability?
  • During DME hold mode, which of the following occurs?
  • When the Captain's NORM/EMER on the Audio Control Panel is selected to EMER, what happens?
  • In EICAS terminology, which color is used to indicate advisories?
  • When the cargo fire protection discharge is activated, how long after the first bottle does the second bottle discharge?
  • After an EICAS Control Panel (ECP) failure, which buttons remain operative?
  • The taxi/recognition light will come on, regardless of its switch position, if which condition occurs?
  • Which statement accurately describes the effect of the ON/OFF state on heating when 115VAC is applied?
  • When are the probes automatically heated?
  • Which of the following statements correctly pairs AHRS initialization times?
  • Flight Spoilers can be used to down to an altitude of ___.
  • APU bleed air can be used in flight up to what altitude?
  • 1/2 BANK is available in TO and GA mode.
  • The FAST position of the window wipers will always override any other position selected
  • Which engine acts as the master during synchronization?
  • Which sources can supply air to the air conditioning packs?
  • Which statement about Mach Trim operation relative to autopilot is true?
  • Emergency lighting is powered by ___ and illuminated automatically with a loss of either AC or DC essential power.
  • The minimum oxygen pressure for dispatch for two cockpit crewmembers is 807 psi.
  • Minimum bleed air pressure for engine start?
  • Which EICAS messages cannot be paged?
  • The statement 'The stick pusher function will not work as long as at least one of the switches is on' is true.
  • What happens if a Cowl Anti-icing Duct ruptures?
  • With a B hydraulic pump in AUTO position, what will cause the pump to operate?
  • In DME hold mode, what happens to the ident?
  • If the automatic temperature control feature of an A/C pack malfunctions, what can the pilot do?
  • If the APU electric fuel pump fails while running, which statement about restarting after shutdown is true?
  • During engine start, is it required for the pilot to select OFF with the AC packs and open the ISOL valve?
  • Where are the reference speeds, MDA, DH, and barometric altimeter settings entered?
  • FADECs power source under 50% N2 with PMA above 50% N2?
  • If the 6th stage bleed path is blocked by a one-way check valve, what is the consequence for bleed air flow?
  • How is the APU started?
  • Which valves fail in the closed position?
  • How are the avionics cooled?
  • How are the avionics cooled?
  • In the pitch mode, rotating the pitch wheel one click provides how much pitch change?
  • How many TRUs does the aircraft have and what are they rated at?
  • On the ground, how long can the EFIS tubes be operated without AC power?
  • What are the APU Starter Limits?
  • What is the total current capacity when all TRUs are operating?
  • Which description accurately reflects the actions performed by the red autopilot disc button on the control wheel?
  • Where is the slip indicator located?
  • How is the Anti-skid test performed?
  • If the APU is rotating above __% in flight or __% on the ground, the APU Electronic Control Unit will inhibit start
  • Minimum pavement width for a 180-degree turn is 75 ft.
  • During PA system use, whose transmission overrides all others?
  • The taxi/recognition lights should be turned OFF if the aircraft is stopped for more than how long?
  • Which air source cools hydraulic systems 1 and 2 during flight?
  • What happens if a Cowl Anti-Icing duct ruptures?
  • Where is the Trim Disc control located?
  • What happens when you press the TOGA switch on the thrust lever in flight?
  • Which condition will illuminate the fault light on the IDG DISC switchlight?
  • When the RA test button is pressed, what should be observed?
  • What bleed air sources supply the PACKs?
  • How will you know that APR power is being scheduled by FADEC?
  • Which statement is true regarding the heating of the drain masts when 115VAC power is applied to the controller?
  • Fuel pressure from the fuel metering unit is used by FADEC to operate which components?
  • If the bleed valves control selector is AUTO, what is the effect of the wind ISOL Valve switch and BLEED AIR SOURCE selector?
  • With the cockpit switch in ARM, loss of power to which bus(s) will activate the emergency lighting?
  • What is the maximum fuel imbalance allowed for takeoff?
  • Cabin pressure is maintained during flight by which mechanism?
  • What is the priority of power sources for each AC bus?
  • How many stages does the N2 compressor have?
  • The red A/P disc button on the control wheel can accomplish two functions. Which of the following describes those functions?
  • What function does the roll disconnect handle perform?
  • Which statement about the ADG deployment scenario is true?
  • When are all probes automatically heated?
  • What happens if the active cabin pressure controller fails?
  • After the failure of ED1, How can the status page be displayed?
  • The wing anti-ice cross bleed selector will allow one engine to be selected even with the bleed valves control selector in AUTO.
  • The emergency lighting system will operate off its dedicated batteries for up to how many minutes?
  • In the NAV mode, is it necessary to fly a full ILS approach with glideslope?
  • Which DC bus is not normally displayed on the DC synoptic page?
  • What does the flight abort mode of the pressurization system do?
  • If the ground spoilers fail to deploy automatically, how else can they be deployed?
  • Which hydraulic system powers the landing gear?
  • What is the normal CF34 thrust rating and its APR thrust?
  • In the vertical speed mode, rotating the pitch wheel one click provides how much VVI change?
  • What does selection of the AFT CARGO SMOKE switch light do?
  • Mach Trim begins to operate at 0.4 Mach and is operable in both manual and autopilot flight operations.
  • With the same indications of an overheated brake on the ground, what should you do?
  • Which parameters does the ACSC monitor to control bleed valves and distribution?
  • What are the maximum positive and negative cabin pressure differentials?
  • What is the primary power source for the potable/wash water system (PWS)?
  • What is the normal hydraulic reservoir quantity range expressed as a percentage?
  • The ESS TRU 2 Tie Contractor's function is best described as:
  • FADECs power source?
  • Which statement is true regarding wing anti-ice operations when the slats are extended?
  • What will selection of the High Power schedule switchlight do?
  • What must you do to return the AC ESS BUS and ACMP 3B pump to normal aircraft power once the ADG deploys?
  • What is the maximum altitude at which a single air conditioning pack can operate?
  • What is the APU starter cutout RPM?
  • What will happen if the Primary Trim Switches on the yoke are activated when the A/P is engaged?
  • What part of the IDG keeps the Generator turning at a constant speed of 12,000 rpm?
  • AHRS initialization takes approximately how much time in MAG, and how much time in DG respectively?
  • If the PFD display fails, how can PFD information be displayed on the MFD?
  • With the bleed valve control in the manual mode, is it possible to provide APU air to the Wing Ice protection system?
  • In flight, when the APU automatic fire protection is engaged, which action occurs?
  • Before using SPEED, V/S or Pitch mode to change altitude, what must first be done?
  • What is the turbulence penetration speed?
  • The nosewheel steering system allows travel of how many degrees from neutral with the rudder pedals?
  • Fuel for the APU is drawn from which tank via which pump?
  • Which busses are powered with no AC power available and the Battery Master OFF?
  • Pitch trim is ___ actuated.
  • Which statement about the effect of windshield HI heat selection is true?
  • Which hydraulic system powers the landing gear under normal operation?
  • Which action selects the manual cabin pressure controller?
  • ADG power provides power to which systems?
  • What is the tolerance specified for the minimum bleed air pressure during engine start?
  • During an EICAS Control Panel power failure, which of the following buttons remains operational?
  • Individual satellites can be deselected from use by entering the identifier for the satellite on the FMS GPS control page.
  • Minimum oil temperature for start on the ground?
  • The two safety valves in the aft bulkhead protect against which conditions?
  • Ground spoilers require which condition to deploy automatically?
  • Where is the Radar Information Line displayed?
  • Which item is included in the ADG power list?
  • The following statement is true: It is not possible to use the APU in the anti-ice system with the Pneumatic system in AUTO, but it can be done with manual control of the bleed air system.
  • Which hydraulic system can be used to assist manual landing gear extension if the main system fails?
  • If the APU door is stuck open or its position is uncertain, what must be done?
  • What is the maximum bank commanded by half-bank mode?
  • Where is the Flight Mode Annunciator (FMA) displayed on the PFD?
  • The EMER DEPRESS switch light allows the outflow valve to open and the cabin will rise to ___. It should NOT be selected at altitudes above ___.
  • The wind ISOL Valve switch and BLEED AIR SOURCE selector will only have an effect if the bleed valves control selector is placed in which position?
  • With a failure of the pilot's RTU, how can the VHF COMM and NAV frequencies be changed?
  • With ED2 failure or automatic transfer from ED1, what happens to the EICAS Control Panel?
  • What warning is associated with oxygen generators?
  • What happens if the CPC microprocessor fails?
  • The maximum altitude for APU bleed air is which value?
  • The two channels of each FADEC will never make a simultaneous input to the engine except when which condition is sensed?
  • Where are the oxygen overboard discharge indicator and servicing panel located?
  • What is the purpose of the Air Conditioning System Controller (ACSC)?
  • What is the maximum altitude for using APU bleed air?
  • Which device provides an alternative to the pilot RTU for tuning VHF frequencies?
  • After the failure of EICAS display ED1, how can the status page be displayed?
  • What should you do if you are unable to raise the gear handle after takeoff?
  • What parking brake condition is required when performing brake wear checks?
  • During a wind shear warning, you should increase pitch up to the Pitch Limit Marker (alpha-margin indicator).
  • Which component provides airspeed, altitude, and vertical speed data to the PFD?
  • With a loss of control power, what will happen to the HPV, PRSOV, and APU LCV?
  • Emergency lights will be powered for approximately ___ during an emergency.
  • Where does the air from the engines used for pneumatics come from?
  • Primary bleed air source for PWS regulation?
  • What is another valid method to test the anti-skid system besides the self-test in the control unit?
  • On the ED2 and fuel synoptic pages, the main tank fuel quantity indications turn amber under which conditions?
  • Which valves in the CRJ bleed system are designated as PRSOVs?
  • During a DCU warning while only one ED is operational, which page will the operable ED display?
  • What will happen to the bearing pointer on the MFD if there is a signal loss?
  • Is it allowable to dispatch with one fire detection loop inoperative for a given area?
  • When DME hold is selected on the PFD, which of the following describes what happens?
  • What is the normal hydraulic reservoir quantity?
  • Starter disengagement should occur at what percent N2?
  • The ___ provides the PFD with data consisting of airspeed, altitude, and vertical speed.
  • When opened from the inside, the main cabin door will normally ___.
  • Which statement correctly describes the impact on braking when only one hydraulic system remains?
  • When do the passenger oxygen masks automatically deploy?
  • How many ACMP hydraulic pumps are on the CRJ-700?
  • Which statement describes the role of ON/OFF in heating when 115VAC is present?
  • If a generator fails in flight, what should happen to maintain AC power?
  • How is the fluid for system one and two cooled?
  • Which component moves fuel from the center tank to the main tanks?
  • Which stages provide bleed air to the aircraft's pneumatic systems?
  • The roll disconnect T-handle does what to unjam the ailerons?
  • What hydraulic pumps are not controlled by the Hydraulic Control Panel?
  • Which ejectors move fuel from the center tank to the collector tanks?
  • Which option correctly states the action when low fuel is detected in the left engine fuel feed line?
  • Drain masts heating status: The drain masts are heated when 115VAC power is applied to the controller, regardless of the controller ON/OFF state.
  • What is the maximum weight rating for the main cabin air stair door?
  • During a one-engine-out event, FADEC will schedule MCT power when the thrust lever is in which detent?
  • What is the max speed for the windshield wipers?
  • Which power sources supply hydraulic pump 3B?
  • Which option correctly states heating behavior with 115VAC and ON/OFF consideration, such that only one option is true?
  • During a starter assisted engine start, you should not try to engage the air turbine starter if the N2 RPM exceeds what percentage?
  • How many ways can you change the setting of VHF NAV number one?
  • When does engine synchronization occur?
  • The wind shear escape guidance from the flight director is guaranteed during wind shear caution.
  • What is the minimum air temperature in flight?
  • LH/RH ENG FIRE PUSH lights do what?
  • What is the minimum oxygen pressure for dispatch for two cockpit crewmembers?
  • When can CAUTION messages be paged and boxed?
  • The bi-directional XFLOW pump turns on when the fuel imbalance between wing tanks reaches how many pounds?
  • When utilizing gravity cross flow in flight, which maneuver can enhance the transfer?
  • On the ED2 and fuel synoptic pages, the main tank fuel quantity indications turn amber under which conditions?
  • Which bleed air sources feed the PACKS?
  • Which valve type is specifically described as ACSC controlled in the CRJ bleed system?
  • In the event of FADEC failure, can the other engine FADEC provide fuel control of both engines?
  • Which warnings are not inhibited when a DCU disable switch is pressed?
  • Which statement about hydraulic pressure is true when the parking brake is set and hydraulics are deactivated?
  • How many independent hydraulic systems provide power?
  • The Air Data Computer receives static air pressure measurements from the ___ to display information on the PFD.
  • What is the minimum oil temperature for start on the ground?
  • If engine start bleed pressure reads 41 psi, is this within tolerance?
  • What does an illuminated fault light on the Auto Xfer switchlight indicate?
  • The hydraulic quantity readout is valid only when the system is pressurized.
  • For the stab trim warning clacker, at what condition and duration does it sound?
  • Where is the Radar Information Line displayed?
  • What should you do before resetting the BTMS after an overheated brake indication on the ground?
  • If a Red Warning message is generated on ED1, what indications will accompany it?
  • Identify the statement in which the ON/OFF state has no influence on heating when 115VAC is applied.
  • If a cabin pressure controller fails, what happens?
  • Which statement reflects heating behavior independent of the ON/OFF state when 115VAC is applied?
  • How many minutes of oxygen will the passenger oxygen generator provide?
  • Which statement correctly states the heating behavior with 115VAC and ON/OFF independence?
  • After ED1 failure, which combination of actions can display the status page?
  • During a wind shear warning, increasing pitch up to the Pitch Limit Marker is recommended.
  • What does the ADG power?
  • To display TCAS information on the MFD, which control must be pressed?
  • Which color CABIN ALT message indicates the altitude is between 8,500 ft and 10,000 ft?
  • Which component primarily regulates cabin pressure by adjusting flow?
  • How many minutes do the oxygen generators provide oxygen?
  • What is the maximum fuel imbalance for takeoff and all other phases of flight respectively?
  • When SEAT BLTS switch is AUTO, under what conditions do the seatbelt signs illuminate automatically?
  • What is the purpose of the ESS TRU 2 Transfer Contractor?
  • Which panel can be used to regain PFD information on the MFD when the PFD fails?
  • When the parking brake is set and hydraulics are deactivated, which component maintains pressure in the #3 brake accumulator?
  • Pressing the ALT button on the FCP will:
  • AHRS Initialization takes approximately how much time on the ground and how much time in flight?
  • Which statement about the anti-skid test procedure is true?
  • What problems will be encountered with HYD 2 LO PRESS message displayed?
  • What powers the DC SERV BUS?
  • Where will a pending oil filter bypass or oil chip detection alert be indicated?
  • At what temperature does the hydraulic high temperature caution activate?
  • Is it necessary to press both TOGA and A/P DISC to disconnect autopilot during go-around?
  • Which items are powered from the DC EMERGENCY Bus?
  • When the pilot moves the control wheel or rudder pedals, what makes the respective lift control move?
  • Identify the true statement among the following about heating when 115VAC is applied.
  • Which EICAS messages cannot be removed?
  • What will happen if one of the two motors that drives the flap panel fails?
  • Which hydraulic system can be used to extend the landing gear if the main system fails?
  • If ESS TRU 1&2 fail, how much would the DC Essential Bus remain powered?
  • ENG Ignition power sources: which statement is correct?
  • Hydraulic pumps pressurize each system to a nominal pressure of ___ PSI.
  • If engine bleed air is unavailable, which alternative sources may supply air to the packs?
  • What are the FADECs powered by?
  • FADEC continues to update its power calculation during takeoff up to which speed and altitude, or until what event?
  • From the following, choose the statement that reflects heating when 115VAC is present.
  • Where are the cargo smoke detectors located?
  • What will be seen on the N2 gauges when the wing anti ice system is activated?
  • Which power source supplies pump 3B?
  • Which idle setting would typically be used during approach?
  • In the event of an engine failure, there will be no way to provide air to the respective wing for ice protection. Which statement is true?
  • What does an illuminated FAULT light on the CABIN PRESS panel indicate and what would you do?
  • If the ground spoilers fail to deploy, how else can they be deployed?
  • Which idle setting would typically be used during landing?
  • Which statement correctly describes heating with respect to voltage and ON/OFF state?
  • What sides of the aircraft are the oxygen 'burst disk' indicator and service panel located respectively?
  • If the pilot RTU has failed, which method allows changing VHF frequencies?
  • During a GPS approach, what allows you to continue the approach to the missed approach point?
  • What effect will the loss of both #2 and #3 hydraulic systems have on the landing gear?
  • Where does the VIB icon appear when vibration limits are displayed?
  • What is the range where the APU starter cut-out will occur?
  • What EICAS messages cannot be removed from view by boxing?
  • Which detent is associated with scheduling APR power during an OEO scenario when the detent is in TOGA?
  • A fault on which buses would cause the Auto Xfer to be inhibited, as indicated by the fault light?
  • After takeoff (no anti-icing required), what causes the bleeds to transfer from the APU to the engines?
  • AHRS initialization time in MAG and DG is approximately?
  • How many hydraulic pumps are on the CRJ-700?
  • The SPEED pushbutton is used to do what?
  • What is the minimum oxygen pressure for dispatch for three cockpit crewmembers?
  • Which component closes to allow the remaining generator to power both AC systems after a generator failure?
  • The turbulence penetration speed is defined as which of the following?
  • The Radar Information Line is displayed on top of the MFD.
  • When DME hold is selected, what is displayed/removed from view on the PFD?
  • What does the FMA in the upper left corner of the PFD display?
  • The ARP is used to enter which of the following?
  • Manual ground spoiler deployment method: which switch setting arms the system?
  • At what RPM percentage does the APU EC Unit inhibit starting when rotating in flight or on the ground?
  • Which hydraulic pumps are not controlled by the Hydraulic Control Panel?
  • If ESS TRU 1 and ESS TRU 2 fail, which interconnections enable TRU to power both the DC BATT BUS and DC ESS BUS?
  • Pitot tubes P1 and P2 are pitot static while the pitot tube P3 is only a pitot tube.
  • What does the AC ESS XFER switchlight do when selected?
  • Which mode is engaged by the SPEED pushbutton?
  • What EICAS messages cannot be paged?
  • The hydraulic high temperature caution activates at what temperature?
  • If HYD 2 LO PRESS is displayed along with loss HYD SYS 3, which problem will be encountered?
  • The maximum altitude for starting the APU is __. It can be operated up to __.
  • Which statement best describes the standby position on the Display/Avionics fan control panel?
  • True or False: If slat travel stops, flaps will continue to their selected position?
  • Which of the following statements about galley heater control is true?
  • If one wing tip navigation light bulb fails, how do you switch to the secondary bulb?
  • Where does fuel to operate the APU come from?
  • How many hydraulic pumps are on the CRJ?
  • What is the purpose of the Isolation Valve?
  • Which statement about cross flow during takeoff is correct?
  • Which button is used to engage the CLB or DES mode?
  • How many wing and anti ice schedules are there?
  • Which option correctly states the AHRS initialization duration?
  • The Autotune function is used to provide FMS control over which component?
  • EMER FLAP action results in which configuration?
  • What does the AFT CARGO SMOKE PUSH do?
  • Which statement about the AFT CARGO SMOKE PUSH is true?
  • How would you select the other auto pressure controller in flight? How would you select the Manual controller?
  • What happens if the APU detects a fire in flight?
  • If the APU electric fuel pump fails while the APU is running, what happens?
  • How many automatic cabin pressure controllers are there?
  • If ice is detected on one of the ice detector probes, the respective ice protection systems will automatically be activated.
  • What is the minimum bleed air pressure for engine start?
  • APU starter limits: how many attempts and wait between attempts?
  • When will the anti-skid system allow braking to occur on landing?
  • When N2 exceeds 50%, which component powers the FADEC PMA alternator?
  • When can caution messages can be paged and boxed?
  • What is the correct pecking order for operation of the stab trim from highest to lowest?
  • In AUTO, under what conditions do the seatbelt signs automatically illuminate?
  • Which panels can be used to regain ECP operation after it is inhibited due to ED failures?
  • Gauges are available to alert the pilot vibration limits in which engine sections?
  • Which items are powered from the DC Emergency Bus?
  • If the main wing tip navigation bulb fails, how is the backup provided?
  • During a Go-Around from Autopilot Couple Approach, you must press TOGA button(s) AND the A/P Disc button on the yoke to disconnect the Autopilot.
  • On the ground, how long can the EFIS tubes operate without AC power?
  • Pressing either TOGA switch does what when airborne?
  • The rudder limiter uses inputs from the ___ and ___ to provide protection from overstress and prevent excessive side slip
  • What are the Ampere-Hour ratings of the main and APU batteries?
  • When the PFD declutters, what is the result?
  • After takeoff (no anti-icing required), what condition causes bleed air to transfer from engine bleed to the APU?
  • Which action automatically powers both the DC Battery Bus and the DC Essential Bus when ESS TRU 1 and ESS TRU 2 fail?
  • How many attempts can be made to reset a failed generator if the checklist calls for it?
  • What is the purpose of the Air Conditioning System Controller (ACSC)?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy