The CRJ-700 has two engine-driven hydraulic pumps, with one serving each independent hydraulic system. This setup helps preserve hydraulic power if a pump or engine becomes unavailable. Electric backup pumps add another layer of support, but they aren’t counted as EDPs.

Multiple Choice

How many EDP hydraulic pumps are on the CRJ-700?

The main idea is that the CRJ-700 uses two independent hydraulic systems, each powered by its own engine-driven pump located on the engine’s accessory gearbox. Because there is one engine-driven pump per system, there are two EDP hydraulic pumps in total. This arrangement provides redundancy so hydraulic power can be maintained if one engine or pump isn’t available. (There are electric backup pumps as well, but they’re not counted as EDPs.)

Engine-Driven Hydraulic Pumps on the CRJ-700

The CRJ-700 uses two engine-driven hydraulic pumps, commonly called EDPs. Each pump is mounted on an engine’s accessory gearbox and supplies hydraulic power to its associated system. That arrangement links hydraulic capacity to engine operation while keeping the two pumps separate. If one pump or engine becomes unavailable, the other can still provide hydraulic power to the functions it serves.

It’s a straightforward count, but the design behind it matters. Hydraulic systems help an aircraft move parts that would be difficult to operate by hand, from flight-control surfaces to landing gear. On a regional jet such as the CRJ-700, dependable hydraulic power is essential—and so is knowing which sources of power are engine-driven and which are not.

What an EDP does

An engine-driven pump converts mechanical power from an engine into hydraulic flow. The engine turns the pump through its accessory gearbox, and the pump moves hydraulic fluid through lines to the components that need it.

Think of the pump as the source of pressure in a network of pipes. The fluid carries force to hydraulic actuators, which then move aircraft components. The pump doesn’t move a control surface directly; it supplies the power that lets the relevant actuator do its job.

The “engine-driven” label is important. It describes how the pump gets its power, not simply what it does. An electric motor-driven pump can also move hydraulic fluid, but it uses electrical power instead of a mechanical connection to an engine. Both types contribute to hydraulic capability, yet they belong to different categories.

That distinction keeps system descriptions clear. When discussing EDPs on the CRJ-700, the count is two—not every pump or backup source that may provide hydraulic power.

Two pumps, two engine connections

The CRJ-700 has two EDPs, with one associated with each engine. Each is installed on the engine’s accessory gearbox, where it can draw mechanical power from the engine.

This arrangement has a practical benefit: the hydraulic pumps are separated by engine. The aircraft doesn’t depend on a single engine-driven pump for all of its engine-powered hydraulic supply. If one engine or its pump is unavailable, the other EDP remains a distinct source of hydraulic power for the system it serves.

That separation is a form of redundancy, but redundancy doesn’t mean every pump can do every job. Each hydraulic circuit has its own design, and the aircraft’s system architecture determines which components receive power from which source. In other words, a second pump adds resilience, but it doesn’t turn the hydraulic network into one big interchangeable pool.

That’s a useful point to keep in mind when reading aircraft system diagrams. Two pumps may look like a simple one-for-one setup, yet the lines, valves, reservoirs, and powered components give each system its own role.

Hydraulic power is not the same as pump count

A common source of confusion is the difference between the number of EDPs and the number of hydraulic power sources overall. The CRJ-700 also has electrically driven pump capability. Those pumps can support hydraulic operation under certain conditions, but they are not engine-driven pumps.

The distinction is similar to having two ways to run a household water pump: one powered by a gas engine and another powered by electricity. Both may move water, but they don’t share the same power source. Counting only the engine-driven units means counting the pumps connected mechanically to the engines.

This matters because aircraft system descriptions use precise terms. “Hydraulic pump” is a broad label. “Engine-driven pump” names a particular kind. If the question is how many EDPs are installed, electric backup pumps don’t change the answer.

Why connect a pump to an engine?

An EDP takes advantage of power that’s already being produced while the engine runs. The accessory gearbox also drives other equipment, so mounting a pump there gives it a direct mechanical connection to the engine.

This design offers a reliable source of hydraulic power during normal engine operation. It also ties pump output to the availability of the engine and its mechanical drive. That’s why aircraft designers use more than one source of hydraulic power: a single source can’t cover every operating condition or failure scenario.

The result is a system with layers. Engine-driven pumps provide hydraulic flow through their mechanical connection. Electrical pumps provide another way to supply hydraulic power when required. The aircraft’s controls and system logic determine how those sources work within the broader design.

It’s a little like keeping both a main pump and a backup on hand—not because the main pump is expected to fail, but because critical systems need more than one route to useful power.

What the two-pump layout means

For a CRJ-700 systems overview, the key fact is simple: there are two engine-driven hydraulic pumps, one on each engine’s accessory gearbox. Their separate engine connections support redundancy, helping preserve hydraulic capability if one engine or pump is not available.

Still, redundancy has limits. A backup source may supply only certain functions, or operate under specific conditions. Likewise, one EDP’s presence doesn’t imply that it can fully replace the other pump across every hydraulic circuit. The details depend on the aircraft’s system design, including how hydraulic lines and components are arranged.

That’s why aircraft systems are best understood as connected parts rather than a list of equipment. The pump count tells us how many engine-driven sources exist. The system diagram explains where their power goes and how other sources fit in.

Keeping the terms straight

A quick way to remember the distinction is to focus on the pump’s power source:

  • An EDP is driven mechanically by an engine.

  • An electric pump is driven by an electric motor.

  • Both can move hydraulic fluid, but only the first counts as an engine-driven pump.

On the CRJ-700, that leaves two EDPs in total. Each is mounted on an engine’s accessory gearbox, and each supplies its associated hydraulic system. Electric pump capability adds another layer of support, but it doesn’t add to the EDP count.

That small naming detail can make a big difference when discussing aircraft systems. Count the source, not just the function: two engine-driven pumps, plus separate electrically driven capability.